-
product
Lifecycle Test System
Model 933
The Model 933A Life Cycle Test System is a low cost, generic test platform used to perform cycling of keypads, keyboards, membranes, switches, or any product requiring fatigue testing.
-
product
54 Piece Automotive Test Connector Kit
146
This comprehensive test kit features a variety of terminal adapter sets which enable connection to most automotive vehicle connectors, both foreign and domestic. Terminal adapters connect via the included 48 inch stacking banana plug test leads. Connection to most DMM’s and scopes is no problem. Kit is designed to provide wide testing coverage and quicken the test process.
-
product
Drop-In Functional Test Fixtures
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
XCITE 1100 Field Test Series
The Xcite 1100 Field Test Series uses the same Exciter Heads and Master Controller as the 1100 Laboratory Series but replaces the 5 GPM 3-Phase Hydraulic Power Supply with a field portable 1.2 GPM Single Phase Power Supply. While providing the same 3000 PSI pressure, the field test unit is switch selectable from 110 V (20 A) to 220 V (10 A) single phase power.
-
product
SFP Based Fiber Optic Test Solution
Eye-BERT Micro
The Eye-BERT Micro is a low cost, easy to use, all-in-one SFP based fiber optic test solution offering high performance bit error rate testing at a fraction of the cost while providing a rich set of features not found in other bit error rate testers. Features include: variable bit rate, user programmable patterns, and optical power and temperature monitoring (per SFP capability). Additionally, with a click of a button, the Eye-BERT Micro will automatically test an SFP module based on the informa...show more -
product
Automated Shock Test Systems
AutoShock-II Test System
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCIe
APEX3910
STANAG3910/EFEX Test and Simulation module for PCIe with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APEX3910 is a functional replacementfor model APE3910.
-
product
Test Systems
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems.
-
product
Application Penetration Testing:
Penetration testing (or pen testing) is a simulated security exercise in which ethical hackers attempts to exploit the vulnerabilities of an application system (web or mobile). The objective of this exercise is to identify any possible loopholes present in the system’s defence mechanism which the real hackers could take advantage of. QA Mentor practices the following stages while exercising this:
-
product
EMI Test Receivers
EMI test receivers; extremely accurate instruments designed to detect electromagnetic emissions rigorously, to ensure all emissions conform to the Standard being tested to. Configured to set up running the required tests for parameters defined by the Standards as simply as possible, including automated test routines. R&S EMI test receivers can be much more too, with a full signal and spectrum analyzer in the same instrument.
-
product
Bench-top Test Jigs
Robust, easily customised, standalone kits for testing a variety of PCB's. Basic hinged-top or cam operated pusher plate, advanced cam-operated gate with fully adjustable pusher-fingers.
-
product
Test Stand, Fixture Design and Manufacture
As your partner, Trialon’s commitment to providing our customers with custom test stands, test and vibration fixtures that optimizes the sample test. Our experienced staff can design and manufacture a test stand or fixture for almost any product.
-
product
Dual Bay Flex 40 For Larger Generic Test Systems
Flex 40
The Flex 40 is generally suited to the larger Generic Test Systems. A Flex 40 is a dual bay version of the Flex 30 that gives us the ability to fit a wide range of external instrumentation, PXI, custom modules and large fixture interfaces. Generally it is fitted with the VPC G12x Interface but this can be changed to suit the requirement.
-
product
Multi-Service Transport Test Solution
MX Series
The VeEX MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
product
Test Research
TRI
REBOUNDER test kits feature two separate "Co-Active Seals", "Quick Twist" Locking Guide Pins, and boards constructed of fine weave G10/FR4, increasing testing reliability and accuracy while simplifying finishing, debugging, and maintenance. All H+W products are backed-up with our "Test-Assured" one year warranty, in writing, and SAME DAY SHIPMENTS
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 43
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
product
Applications
No matter what the requirement for ultra high-precision measurement, VIEW has the ideal solution. VIEW non-contact measurement systems utilize sub-pixel image feature detection with either field-of-view (FOV) or point-to-point (PTP) configurations for exceptional accuracy and repeatability. From etch-dimensions on hard disk drive (HDD) heads to semiconductor overlay measurements, we provide the accuracy you need for quality manufacturing.
-
product
Test Automation Platform
Askida CT
Askida CT changes the way automated tests are carried out. It is the only platform on the market that lets you do true end-to-end testing automation without requiring deep technical skills. You can easily define your testing strategy and convert your manual tests into automated ones in one simple click.
-
product
Pump Test System
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
product
Liquid Test Fixture
16452A
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
product
Universal OTP Functional Test System for the Production of Level and Fluid Sensors
Multifunctional function tester with parallel test function based on the LXinstruments OTP2 system platform. The system is used for assembly, final test and calibration of liquid and level sensors for commercial vehicles, construction machinery and shipbuilding in a high mix / medium volume environment.
-
product
Electrodynamic Vibration Test Systems
PET-series
Vibration controller: Enables complicated vibration tests being coupled with the vibration controller.
-
product
Custom Designed Test Fixtures
We specialize in automated test systems for both RF and digital devices, modules and systems. Please call to discuss your test requirements.
-
product
Optical Materials & LiDAR Test Equipment
Is a remote sensing method which is used to estimate the range between two objects.
-
product
Cable Fault and Test System Vans
Whether you are working on-site, in the countryside or an urban environment, having the right equipment available when conducting fault location operations is vital. When the correct tools can be accessed easily, fault-location time speeds up dramatically, and faults can be dealt with more efficiently. Megger’s range of cable test vans offer solutions to the challenges of fault location in the real world, no matter the environment. Our test van systems have been developed in collaboration with e...show more -
product
Fetal & Neonatal Test Equipment
Setting a new performance standard in Fetal/Maternal simulationTwo direct Fetal ECG'sFive full Maternal ECG leadsFour separate Fetal ECG tracingsThree Fetal ultrasound channels with "Triplets" capabilityThirteen Fetal static ECG ratesFifteen trends of Fetal data representing real-life case studies
-
product
Design for Test
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test p...show more -
product
Salt Spray Corrosion Test Chamber
CX-Y60L
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Salt Spray Corrosion Test Chamber for Nss / Acss / Cass Test is used to test the anti-erosion quality of the surface of all materials after the rust-proof of painting, coating, electroplating, anoding and rust-proof of greasing.anti corrosion treatment for a variety of materials, corrosion resistance of their products.
-
product
Basic Unit - Medical Equipment Functional Test Module System
GS-X
The GS-X Testing System consists of a Basic Unit and various plug-in test modules which the user can purchase as required. The range of functions of these Module-Box is being continuously expanded, and presently includes functions for testing the following devices: - Infusion pumps, Cardiac pacemakers, Defibrillators, High-frequency Surgical equipment, electrical safety ECG Simulation, Equipment for electro-stimulation.
